EVOC EC3-1813 Series User Manual

EC3-1813CLD2NA（B） 基于 Intel Luna Pier 平台 3.5 寸主板 3.5 ″ Motherboard Based on Intel Luna Pier Platform Version:C00

Chapter 2 Installation EC3-1813CLD2NA(B) - 5 - Chapter 2 Installation Product Outline H1H2H4H3 Unit: mm Warning! Please adopt appropriate screws a

Chapter 2 Installation - 6 - EC3-1813CLD2NA(B) Locations of Connectors H1JP1JP2JP4JP3JP5COM2KM1COM1JCC1COM3GPIO1J3COM4LPT1VGA1LAN1J2LAN2AUDIO1H2H4

Chapter 2 Installation EC3-1813CLD2NA(B) - 7 - Structure ICH8MBIOSSuperI/OPCI-104PCI BUSPCIe X12.0 UHCI/EHCIKB/MOUSELPTCOM1&COM3&COM4 RS2

Chapter 2 Installation - 8 - EC3-1813CLD2NA(B) Jumper Setting 1. Clear/Keep CMOS Setting (Pitch: 2.0 mm) CMOS is powered by the button battery on

Chapter 2 Installation EC3-1813CLD2NA(B) - 9 - 4. Choose Mode for COM2 (Pitch: 2.0mm) Mode Selection Pin Setting RS-232 (Default) RS-422 RS-485

Chapter 2 Installation - 10 - EC3-1813CLD2NA(B) 2) Single-channel 18-bit LVDS Connector Pin Signal Name Pin Signal Name 1 LVDS_D0+ 2 LVDS_D0-

Chapter 2 Installation EC3-1813CLD2NA(B) - 11 - Audio Connector The board provides one 2x5Pin AUDIO pin header (Pitch: 2.0mm). Pin Signal Name P

Chapter 2 Installation - 12 - EC3-1813CLD2NA(B) LPT Connector The board provides one 2x13Pin LPT connector (Pitch: 2.00mm); the pin definitions ar

Chapter 2 Installation EC3-1813CLD2NA(B) - 13 - Hot-swap of SATA Hard Disk Notes for hot-swap of SATA hard disk: 1. The hard disk shall support S

Chapter 2 Installation - 14 - EC3-1813CLD2NA(B) Step 2: Please connect the SATA data cable to the SATA connector on board. Step 3: Please connect

Copyright Notice Information offered in this manual is believed to be correct at the time of printing, and is subject to change without prior notice

Chapter 2 Installation EC3-1813CLD2NA(B) - 15 - LAN Port 1. The board provides one standard 10/100/1000Mbps RJ45 port. LAN1 LILED (Dual-Color: O/

Chapter 2 Installation - 16 - EC3-1813CLD2NA(B) USB Port 1. The board provides one dual-layer 90-degree A Type USB port with shielding. Pin Signa

Chapter 2 Installation EC3-1813CLD2NA(B) - 17 - GPIO Connector The board provides one 2x5Pin GPIO pin header (Pitch: 2.0mm). Pin Signal Name Pin

Chapter 2 Installation - 18 - EC3-1813CLD2NA(B) 3) Loudspeaker Output Connector (Pitch: 2.54mm) Pin Signal Name 1 SPEAKER 2 NC 3 GND FP3 4 +5V

Chapter 2 Installation EC3-1813CLD2NA(B) - 19 - CF Connector The board provides one standard CF card socket (CF1, on the rear of the board). Pin

Chapter 2 Installation - 20 - EC3-1813CLD2NA(B) PCI-104 Bus Expansion Connector The board provides one standard PCI-104 bus expansion connector

Chapter 2 Installation EC3-1813CLD2NA(B) - 21 - Configuration instructions for VGA + LVDS dual display output, take XP system as an example: Displ

Chapter 2 Installation - 22 - EC3-1813CLD2NA(B) 4. Click “OK” and the dual display clone mode is set. Display the Second Display via Extended

Chapter 2 Installation EC3-1813CLD2NA(B) - 23 - 2. Set the models of the primary display and the secondary display in “Primary Display” and “Seco

Chapter 3 BIOS Setup - 24 - EC3-1813CLD2NA(B) Chapter 3 BIOS Setup BIOS Overview BIOS (Basic Input and Output System) is solidified in the flash m

Safety Instructions 1. Please read this manual carefully before using the product; 2. Leave the board or card in the antistatic bag until you are

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 25 - Basic Function Setting for BIOS After starting SETUP program, the main interface of CMOS Setup Utili

Chapter 3 BIOS Setup - 26 - EC3-1813CLD2NA(B)  Advanced BIOS SETUP UTILITY Advanced Settings WARNING: Setting wrong values in below sections may

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 27 -  Hyper Threading Technology Control switch for Intel Hyper Threading Technology function.  Int

Chapter 3 BIOS Setup - 28 - EC3-1813CLD2NA(B)  Configure SATA as SATA controller type selection, it is corresponding with the options of IDE, RA

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 29 -  AHCI Port0 ~ 2 Configuration menu for AHCI port, it is displayed only when the SATA controller is

Chapter 3 BIOS Setup - 30 - EC3-1813CLD2NA(B)  Serial Port 1-4 Address Set the addresses of serial port 1-4 on motherboard, the options are: Dis

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 31 -  Vcore CPU core voltage;  V3.3/ V5.0/V12.0/VBAT Turn on/off power to output voltage;  USB Con

Chapter 3 BIOS Setup - 32 - EC3-1813CLD2NA(B)  USB Mass Storage Device Configuration This option is used configure the USB mass storage device,

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 33 -  Clock Generator Configuration BIOS SETUP UTILITY Configure Clock Generator Spread Spectrum Contro

Chapter 3 BIOS Setup - 34 - EC3-1813CLD2NA(B)  DRAM Frequency Configure the frequency for DRAM; it is recommended to use automatic modification

Contents Chapter 1 Product Introduction...1 Overview...

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 35 -  PCIPnP BIOS SETUP UTILITY Advanced PCI/PnP Settings WARNING: Setting wrong values in below sectio

Chapter 3 BIOS Setup - 36 - EC3-1813CLD2NA(B)  Quick Boot During BIOS booting period, configure whether to permit skipping certain test to reduc

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 37 -  Exit BIOS SETUP UTILITY Exit Options Save Changes and Exit Discard Changes and Exit Discard C

Chapter 3 BIOS Setup - 38 - EC3-1813CLD2NA(B) System Resource Managed by BIOS under X86 Platform We define three kinds of system resources here:

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 39 - Address Device Description 000h - 00Fh DMA Controller #1 010h - 01Fh Carrier Resource 020h - 021h P

Chapter 3 BIOS Setup - 40 - EC3-1813CLD2NA(B) 0E0h - 0EFh Carrier Resource 0F0h - 0FFh Numeric Data Processor 1F0h - 1F7h Primary IDE 274h – 277h

Chapter 3 BIOS Setup EC3-1813CLD2NA(B) - 41 - which is assigned by BIOS or OS. Interrupt assignment of some devices of X86 platform is shown in th

Chapter 4 Installing the Drivers - 42 - EC3-1813CLD2NA(B) Chapter 4 Installing the Drivers Regarding the driver program of this product, please re

Appendix EC3-1813CLD2NA(B) - 43 - Appendix BPI Overview EVOC BPI (BIOS Programming Interface) is a cross-platform, easy-maintenance software inte

Appendix - 44 - EC3-1813CLD2NA(B) 5、 Low Cost Developing the applications by BPI will not increase additional hardware and software cost, but i

Audio Connector... 11 Serial Port ...

Appendix EC3-1813CLD2NA(B) - 45 - Troubleshooting and Solutions NO. Phenomenon Troubleshooting and Solution Analysis: it could be the problem of

Appendix - 46 - EC3-1813CLD2NA(B) when installing the CD-ROM, which leads to poor connection of the hard disk data cable, or the master and slave

Chapter 1 Product Introduction EC3-1813CLD2NA(B) - 1 - Chapter 1 Product Introduction Overview EC3-1813 series are embedded motherboards with low

Chapter 1 Product Introduction - 2 - EC3-1813CLD2NA(B) Temperature: -20C ~ 60C; -20C ~ 70C (with fan); Humidity: 5% ~ 95% (non-condensing); 

Chapter 1 Product Introduction EC3-1813CLD2NA(B) - 3 - 667MHz Un-buffered NON-ECC DDR3 memory stick up to 1GB. The maximum memory capacity support

Chapter 1 Product Introduction - 4 - EC3-1813CLD2NA(B) Watchdog Function  255 levels, programmable by minute or second;  Supports watchdog tim